We have noticed this article relating to A Step-by-Step Guide to Installing a Bathtub down the page on the web and figured it made good sense to talk about it with you in this article.
Installing a bathtub isn't exactly rocket science, but it does require solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old tub with a new one is likewise a moderately challenging project. If the old tub is easily easily accessible, the job can move rapidly; if you have to open a wall to remove the old bathtub and also place the brand-new bathtub, the task is a lot harder. In either situation, the job is within a home handyman's skills, although you will certainly require an assistant to move out the old bathtub and also embeded in the brand-new one. See to it you have actually certified yourself for the task as well as are comfortable attempting it. Instead of employing a professional to take over a halfway-completed task, it is far better to take into consideration utilizing one before you start. Opportunities are you may require a specialist plumber to make tube links.
This short article will aid you mount a brand-new bathtub in your bathroom if you have actually currently purchased a new bathtub and do not require to alter the setup of your previous water system pipes.
Your tools and also material checklist need to make up the following:
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The process of eliminating the existing taps can be fairly problematic as a result of the restricted accessibility that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the staying water that will originate from the pipes. When the supply pipelines have been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning during this procedure. Once the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing compound.
Prior to moving on to fit the new faucets, compare the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to prevent damages to the string. One end of the port fits on the plastic tail of the faucet and the various other end offers a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the tap in the installing opening in the bath/basin ensuring that the washers remain in area between the tap and the sink. Secure the faucet in position with the manufacturer provided backnut. When the faucet is safely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous kind needs to be connected to the tap ends first, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Bathtub
Using the two wooden boards under its feet, put the tub in the called for placement. The wood boards are handy in evenly spreading the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The following goal is to guarantee that the tub is leveled all round. This can be accomplished by examining the level as well as changing the feet on the bath tub until the spirit level reads level.
To install taps, fit the bottom of the furthest flexible tap connector to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the other faucet.
Activate the water and also examine all joints and also brand-new pipework for leaks and tighten them if essential. Load the bath tub as well as likewise check the overflow outlet and also the typical outlet for leaks.
Ultimately, deal with the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the tub ought to wait up until the bathtub has actually been used at the very least when as this will certainly settle it into its last setting.
Getting ready for the Installation
To start with, the sustaining frame supplied with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the tap features a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps device to avoid strain on the tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now prepare to be fitted in its last position.
Tiling Around the Tub
In the location where the bath meets the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to fracture a stiff seal, triggering the water to penetrate the wall in between the bath as well as the tiling, resulting in difficulties with dampness as well as feasible leaks to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your components and fittings. They are offered in tubes and also cartridges, and can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched paper or soft rope. Remember to always fill up the bath tub with water before sealing, to allow for the activity experienced when the bathtub is in use. The sealer can fracture fairly early if you do not take into consideration this activity prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily available on the market. It is a good idea to fit the floor tiles making use of waterproof or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very drawn to How to Install a Bathtub Yourself and I'm hoping you appreciated our blog posting. Those who enjoyed our blog entry please make sure you remember to pass it around. Thanks a lot for going through it.
Request Free Estimate